Delivery, Setup, and Installation (Highly Recommended)
- Phoenix Metro - $225
- Arizona (Outside Phoenix) - $399
- Continental USA - $599
<NYC - $649>
*Note: Arizona Wall Bed does not make money on shipping and installation.
These prices reflect the actual cost for us to get our product to you.
Should for whatever reason it cost less for delivery, you will be refunded the excess money.
- Phoenix Metro - $225
- Arizona (Outside Phoenix) - $399
- Continental USA - $599
<NYC - $649>
*Note: Arizona Wall Bed does not make money on shipping and installation.
These prices reflect the actual cost for us to get our product to you.
Should for whatever reason it cost less for delivery, you will be refunded the excess money.
Arizona Wall Bed Phoenix Murphy Beds - Direct From The Factory
| 602.889.5725 |
Wall Bed Tune-Up Page
The advanced design of a Selby bed mechanism will permit you to make simple adjustments. If you move to a new
home, your Selby Wall Bed can move with you. If you choose to replace your original mattress with a new one of a
different weight or thickness, your Selby hardware can be adjusted to accommodate your change. Finally you may
note a change brought on by natural causes over time that require a system tune-up. Your Selby Bed mechanism
will allow the needed adjustment.
Adjustment Procedure
Do Not Attempt to Adjust the Tension with the panel door in the full open position
1. With the cabinet secured to the wall you may start the adjustment procedure
2. Lower the panel door to an approximate 15° angle (from vertical) and tighten by hand
both left and right tension regulators until they no longer turn without force. This means
that both sides are now evenly adjusted and that the springs are uniformly engaged.
3. Unwind the regulators an even 10 full turns each
4. Lower the panel door to 45° and carefully install the chosen mattress. Carefully release
the panel door to see if it will remain at this angle. With a foam mattress the panel door may
stay at this position but a spring mattress will require further adjustment.
5. Bring the bed back up to the original 15° angle (from vertical) At this point, you must use
a 24mm socket wrench to tighten both regulators an equal number of turns in multiples of 8 to
10 turns at a time. One side then the other. A ratchet wrench and 24mm socket is recommended
to avoid damage to the tension adjusting screw cover.
6. Lower the panel door until the bed is parallel to the floor. At this point, you may judge for
yourself the weight of the bed. If you feel it is to heavy, tighten the regulators further
(Always in the up-right position) to obtain the perfect setting.
7. Your new Selby wall bed is now ready for use.
The advanced design of a Selby bed mechanism will permit you to make simple adjustments. If you move to a new
home, your Selby Wall Bed can move with you. If you choose to replace your original mattress with a new one of a
different weight or thickness, your Selby hardware can be adjusted to accommodate your change. Finally you may
note a change brought on by natural causes over time that require a system tune-up. Your Selby Bed mechanism
will allow the needed adjustment.
Adjustment Procedure
Do Not Attempt to Adjust the Tension with the panel door in the full open position
1. With the cabinet secured to the wall you may start the adjustment procedure
2. Lower the panel door to an approximate 15° angle (from vertical) and tighten by hand
both left and right tension regulators until they no longer turn without force. This means
that both sides are now evenly adjusted and that the springs are uniformly engaged.
3. Unwind the regulators an even 10 full turns each
4. Lower the panel door to 45° and carefully install the chosen mattress. Carefully release
the panel door to see if it will remain at this angle. With a foam mattress the panel door may
stay at this position but a spring mattress will require further adjustment.
5. Bring the bed back up to the original 15° angle (from vertical) At this point, you must use
a 24mm socket wrench to tighten both regulators an equal number of turns in multiples of 8 to
10 turns at a time. One side then the other. A ratchet wrench and 24mm socket is recommended
to avoid damage to the tension adjusting screw cover.
6. Lower the panel door until the bed is parallel to the floor. At this point, you may judge for
yourself the weight of the bed. If you feel it is to heavy, tighten the regulators further
(Always in the up-right position) to obtain the perfect setting.
7. Your new Selby wall bed is now ready for use.
